Guidance

Counter pollution stockpiles

Updated 23 July 2021

Current stockpile arrangements

The Maritime and Coastguard Agency’s (MCA) counter pollution equipment and dispersant are distributed across several strategic locations around the UK.

There are three equipment stockpiles, situated in Bristol, Barnsley and Dundee. The location of these sites enables the MCA’s contracted pollution responders to reach any part of the coast on the UK mainland and ferry terminals to Northern Ireland within 12 hours. The equipment stockpiles contain oil spill response equipment for use offshore, near to shore and on the shoreline. The equipment is intended primarily for the deflection, containment, recovery and temporary storage of oil. A number of specialist items of ancillary equipment are also kept in the stockpile, including all-terrain vehicles and a portable inert gas generator.

The UK’s 1400 tonnes of Type 3 dispersant are currently stored at eight stockpiles across the UK. Two large stockpiles are situated near Nottingham and Glasgow, in close proximity to East Midlands and Prestwick airports respectively, where the dispersant can be loaded on to the MCA’s aircraft for aerial spraying campaigns. A small quantity of dispersant is kept at each of these airports to enable rapid mobilisation for a test spray. The remaining four smaller satellite stockpiles in Milford Haven, Belfast, Stornoway and Shetland enable mobilisation to response vessels for ship mounted spray campaigns in those areas. This catalogue gives an overview of the MCA’s stockpiles.

Map of UK Marine Counter Pollution Resources

Aircraft

System	Role	Location
Boeing 737	Large scale dispersant application	East Midlands Airport – can be forward deployed to Prestwick Airport or another suitable airfield in the event of a mobilisation
Beechcraft King Air 200	Aerial verification	Doncaster Airport

Emergency Towing Vessel

Vessel name	Type	Role	Location
Ievoli Black	Anchor Handling Tug Supply Vessel	Emergency towing	Patrol area from the Western Isles to the Shetland Islands

                                                                                                    |

Counter Pollution Equipment

Off-shore equipment

System	Overall quantity	Barnsley	Bristol	Dundee
Current Buster 6	3	1	1	1
Current Buster 4	2	2
Current Buster 2	2	2
Current Buster Pumping System	1	1
Heavy Oil Skimmer	3	1	1	1
Tar Ball Skimmer (Small)	2	2
Tar Ball Skimmer (Large)	2		1	1
Combination Skimmer System	3	1	1	1
Weir Skimmer	5	2	1	2
Heavy Duty Offshore Boom	2400m	1400m	400m	600m
25 Tonne Flexible Floating Storage Tank	24	12	6	6

Shoreline/inshore equipment

System	Overall quantity	Barnsley	Bristol	Dundee
Shallow Draft Combination Skimmers	5	2	1	2
Mini-vacuum Skimmers	6	6
Manta Ray Head	11	7		4
Brush skimmer	3	1	1	1
Rock Scrubber	2	1		1
Rope Mop	2		1	1
10,000L Temporary Storage	62
1,500L Fastank Rapides (for decontamination)	23	15	4	4
All-Terrain Vehicles (ARGO Cat)	7	5	1	2
Inflatable Tents	6	4	1	1
Spate Pumps	9	4	2	3
Rope Mop	2		1	1
Fence Boom	1400m	600m	400m	400m
Shore Sealing Boom	4310m	2825m	455m	1030m
Inflatable Skirt Boom	5910m	3060m	460m	2390m
Rapid Deployment Solid Floatation Boom	600m	600m
Disk Skimmers	5	3	1	1
Sorbent boom	Large quantities at each stockpile

Ancillary equipment

System	Overall quantity	Barnsley	Bristol	Dundee
Inert Gas Generator	1	1
Intrinsically Hydraulic Safe Power Packs	9	5	2	2
Back Up Unit for Intrinsically Safe Hydraulic Power Packs	4	2	1	1
General Purpose Hydraulic Power Packs (not already assigned to specific systems)	13x Vikoma GP10 Mark 2-e, 2x Desmi 50kW	9	3	3
Heavy Oil Pump	1	1
Cargo Transfer Pump TK80 Oil/Water	4	2	1	1
Cargo Transfer Pump TK80 Chemical	2	2
Cargo Transfer Pump TK5 (s/s hoses)	2	2
Cargo Transfer Pump TK5	2	1		1
Cargo Transfer Pump TK150	4	2	1	1
Cargo Transfer Pump TK6	6	4	1	3
Gas Freeing Fans	4	4
Safe zone Air Compressor	1	1
General Purpose Air Compressor	2	2
Trailer Mounted Pressure Washers	3	1	1	1
Inflatable Tents	10	6	2	2
Inflatable Fenders	4x 4m, 2x 12m	6
Portable Lighting Systems (intrinsically safe)	20	20
Self-Contained Breathing Apparatus Sets	8	8
Personal Air Quality Monitors	12	12
Area Gas Monitors	4	4
Radios	For all team members

Aerial capability

Beechcraft King Air 200

Application

The current MCA contract includes two King Air surveillance aircraft operated by 2Excel Aviation.

Remote-Sensing Equipment

The remote sensing system can detect and evaluate pollution and conduct surveillance on the sea both day and night, in all weathers. The main components: * Osprey 30 – Surveillance Radar * Optimare LWIR/UV Line Scanner – pollution detector and quantification * MX15 HD – Electro Optical, IR Sensor * Rhotheta SAR DF – Direction Finding of VHF/UHF/EPRB transmissions

Locations

Doncaster Airport

Piper Navajo ‘Panthers’

Application

These aircraft will provide a temporary additional line of tasking during busy periods and at other times will provide a layer of resilience in the service.

Remote-Sensing Equipment

Wescam MX-15 HD Electro Optical (EO) sensor with both wide and narrow fields of view (for day and low light conditions) and Infra-red: * Geo pointing * Auto tracking * Haze penetration * Image enhancement

Boeing 737

Application

The Boeing 737 has an installed dispersant spray system. This system can be used for a bulk spray of dispersant as part of a to larger-scale dispersant spraying operation.

This aircraft has a maximum spraying capability of 900 metric tonnes over 48 hours (seasonal – depending on hours of light within a day). The plane would spray from between 150 – 200 ft and can perform a round trip of circa 400 nautical miles with 25 minutes on-scene over a circa 3-hour operation with loading and reloading.

Dispersant Spraying System

The dispersant spraying system consists of 7 tanks individually palletised. There is a self-contained palletised diesel pump capable of pumping 400 – 800 US gallons per minute through two spray nozzles. The aircraft can carry up to 18m3 of dispersant at any one time and spraying is controlled from the cockpit.

Note – The Boeing 737 is currently not operational but will be within the next few months.

Locations

East Midlands Airport, with occasional forward deployment to Prestwick Airport.

Emergency Towing Vessel (ETV)

Application

The primary purpose of the ETV is to protect the UK coastline from the potential threat of pollution from any vessel.

Specifications	Value
Built	2010
Call Sign
Bollard Pull	120 tonnes
Registered	Italy
Gross Tonnage	2283 tonnes
Deadweight	2064 tonnes
Dimensions LOA	70m x 15.5m
Draft	5.1m
Crew	13

Mobilisation within half an hour of being called.

Propulsion and Positioning

Built to RINA class it has fifi1 and DP2 capabilities. Propulsion follows a conventional two engine, twin controllable-pitch propeller configuration, powered by two Wärtsilä 12V M26 main engines developing 7,440kW at 900rpm turning 3,400mm propellers in nozzles. Maneuvering is enhanced with two bow and one stern tunnel thrusters.

Deck Equipment

Deck equipment provision is extensive, dominated by a Fukushima anchor-handling/towing winch with brake capacity 3,922kN, each drum having capacity for 1,500m of 72mm wire.

Fire Fighting

FFS supply the fire-fighting installation, two centrifugal pumps supplying two 1,200m³/hr dualflow monitors on the wheelhouse roof

Offshore equipment

Current Buster Systems

Application

The Current Buster system is a containerised inflatable towed skimmer assembly designed to collect, contain and separate spilled oil at speeds ranging from 0.5 to 5 knots in reasonable weather conditions. The systems can be towed between two vessels, or a single vessel utilising a ‘Boom Vane’. The skimmer system is deployed from a hydraulically driven reel, mounted within a 10ft by 8ft frame, fitted with a hydraulic power pack.

• The Current Buster 6 has a 34m opening, is 62.9m in length and can collect in its separator section up to 70m3 of oily water mix (two parts oil to one-part water), wherein a pump or skimmer heads can be placed for the recovery of oil to a temporary storage system. It can be deployed in approximately 25 minutes using 6 experienced operators.
• The Current Buster 4 has a 23-metre opening, is 35.2m in length and its separator section has a capacity of 35m3. It can be deployed in 20 minutes using 5 experienced operators.
• The Current Buster 2 has a 15m opening, is 27m in length and its separator section is 15m3. The current buster 2 as the smallest of the 3 Current Busters is deployable in circa 10 minutes.

Locations

Barnsley: 2x CB6, 2x CB4, 2x CB2, Dundee: 1x CB6

Specifications	Current Buster 2	Current Buster 4	Current Buster 6
Freeboard	600mm	800mm	1000mm
Towing Speed	3 knots	4 knots	5 knots
Total Length	27m	35.2m	62.9m
Front Opening	15m	22m	34m
Separator	15m3	35m3	70m3
Deployment Time	10 mins	10-20 mins	25 mins
Boom Reel Size	3m3	5m3	10m3
Container Size	8ft	10ft	10ft
Total Weight plus Container	2500kg	3200kg	4400kg

Current Buster Pumping System

Application

A weir skimmer specifically designed to be integrated with either the Current Buster 4 or 6. The skimmer head is deployed and secured in the collection area of the Current Buster, from which an umbilical hose, secured to either the port or starboard side sweeping arm, leads back to a pump and power pack on the deploying vessel.

Recovery rate

70m3 per hour

Location

1 system stored at Barnsley

Heavy Oil Skimmer

Application

A mechanical skimmer for use offshore on viscous oils (including weathered heavy fuel oil and mousses

Specification

The skimmer has two banks of 21 toothed discs driven independently by hydraulic motors which recover oil into a positive displacement pump rated at 100m3/h. The system has a draught of 610mm.

Ancillaries

There is a separate control console. The unit is powered by a diesel driven hydraulic power pack.

Weight

480 kg Skimmer (without hoses) 104 kg Control Console Total weight 728 kg

Locations

1 x Barnsley, 1 x Bristol, 1 x Dundee

Tar Ball Skimmer (Scan Trawl)

Application

Scan trawl systems are for the recovery of floating tar balls, fuel oils, oil contaminated debris and asphalt/bitumen residues from oil or emulsion spills. The skimmer is able to filter the water, trapping the heavy oils in a trawl net when equipped with a heavy-duty cover tube. The entrance net has sweeping wings, which guides oil into the trawl bag. Up to three trawl bags can be positioned behind the entrance net. The system can be rapidly deployed from small workboats and a simple air blower for the inflation of the sweeping wings is required.

Dimensions

Small – 2440mm x 1220mm x 1330mm Large – 1800mm x 1210mm x 2500mm

Weight

Small: 162kg Large: 500 kg

Location

2 x Small at Barnsley, 1 x Large at Bristol, 1 x Large at Dundee Specification

Specification

Description	Small System	Large System
Sweeping Wings in PVC/Polyester	2 x 5 metres long	2 x 20 metres long
Net Skirt Draft	0.500 meters	0.77 metres
Volume	2 m3	10m3
Number of Trawl Bags	1	3
Mesh Size	3 – 5 mm	3 – 5 mm

Terminator Skimmer / Combination Skimmer System

Application

The combination skimmer system is designed to recover a range of spilled oils using interchangeable modules. Using the brush module pictured, the system can recover Heavy Oils. By changing the brush module for the disc module, the skimmer can be used for recovery of lighter oils. Also available is a rope-mop and belt module to further increase the versatility of the system. By removing the head assembly altogether, the DOP pump can be used as a standard salvage pump. The unit is driven by a hydraulic power pack, which includes a remote operation station to allow operators a more flexible system layout.

Specification

Dependent upon the grade of oil, recovery rate is up to 100 tonnes per hour.

Dimensions

3048 x 2438mm x 2590mm

Weight

2200 kg

Locations

1 x Barnsley, 1 x Bristol, 1 x Dundee

Weir Skimmer

Application

A weir skimmer for use on light to medium oils. The pump unit is easily detachable and can be used as an emergency offloading pump. For best results, the skimmer requires a calm sea and wind conditions.

Specification

Optimum recovery is 70m3/hr. The pump unit has a cutting edge for dealing with soft debris that may be mixed in with the oil or water. The skimmer system has a dedicated power pack. Engine: Lister HR3 34KW at 2200 RPM, hydraulic start. Maximum hydraulic pressure is 210 bar, maximum flow 140 LPM. An air compressor for altering weir height is fitted – 10 bar, 240 LPM, accumulator capacity 50L.

Ancillaries

Dedicated hydraulic power pack, extension hose reel, spares box.

Dimensions

Skimmer Head 1870mm x 1020mm x 1100mm Power Pack 2000mm x 1230mm x 1400mm

Weight

Skimmer Head 372 kg Power Pack 1400 kg

Location

2 x Barnsley, 1 x Bristol, 2 x Dundee

Heavy Duty Offshore Boom

Application

Designed to be deployed over the stern of a vessel and attached to towing vessel in open waters.

Specification

HD boom is manufactured from heavy duty neoprene rubber with a Hypalon external skin. The construction is seamless and has high abrasion existence and high tensile strength. Flotation is obtained by inflating sections of boom with an air blower. A power pack is required to deploy and recover boom, ensuring that the boom reel is secured to the vessel. The boom has galvanised ballast/tension chain to keep the boom upright when deployed.

Dimensions

Overall: 1.30 metres

Freeboard: 0.50 metres

Draft: 0.80 metres

Ballast: Galvanised chain

Section: 50 metre (4 per reel)

Connectors

ASTM

Weight

4030 kg per 50m section

Locations

9 x 200m Barnsley 1 x 200m Bristol 2 x 200m Dundee

Deployment Requirement

2 x vessels or 1 vessel with utilisation of Boom Vane, with vessel crew and 6 -person deployment team.

25 Tonne Flexible Floating Storage Tank

Application

The flexible floating storage tanks are primarily for use as temporary storage of oil recovered at sea and would be used in conjunction with other oil spill recovery equipment, including containment devises and skimmers/pumps. The tank is manufactured from reinforced double-faced neoprene and can store and approximately 25 tonnes of recovered oil. Full, the bag can be towed up to a maximum speed of 6 knots. Inflatable chambers in the top surface maintain buoyancy above the surface of the water, where filling and discharge connections enable decanting to larger storage facilities if necessary. Tank ends can also be opened for cleaning, this allows for use and reuse for exercises. Included with this product are fluid transfer pumps and air blowers for inflation of the buoyancy chambers, allowing for quick and proper application.

Dimensions

Flat width 2570mm, Flat length 17750mm

Weight

Dry 138 kgs

Locations

18x at Barnsley, 3x at Dundee, 3x at Bristol

Shoreline equipment

Shallow Draft Combination Skimmers

Application

A shallow draft combination skimmer system for use in shallow waters close to the shoreline. This is a modular system with interchangeable ‘wheels’ with either brush, oleophilic disk or drums, allowing for the recovery of most oil viscosities. The system is light and portable and can be carried manually by two responders.

Locations

3x at Barnsley, 1x Bristol, 1x Dundee

Technical specifications

Specification	Value
Length	852 mm
Width	853 mm
Height	464 mm
Weight	22.5 kg
Draft	128 mm
Capacity w/ Brush Wheel	26.8 m³/h*
Capacity w/ Disk Wheel	15 m³/h
Hydraulic Flow	1-3 l/min
Hydraulic Pressure	60-100 bar
Power Requirement	<0.5 kW
Free Water Collected w/ Brush	<2%

Mini Vacuum Unit

Application

The Mini Vac System is a lightweight and mobile vaccum skimming system consisting of vaccum pump, transfer pump, hopper and lance.

The system has a vacuum pump with a capacity of 1980 lpm and a vacuum of - 0.89 at 1500 rpm. The diesel engine has electric and recoil start.

Dimensions

1100mm length x 700mm x 600mm high

Weight

88 kg

Location

6x at Barnsley

Manta Ray Skimmer Head

Application

This is a semi-submerged suction head used for the recovery of oil from the water surface. This product must be used in conjunction with a vacuum skimmer or a spate pump.

Dimensions

600 m length x 1200 mm wide x 60 mm high

Weight

12 kg

Locations

7 x Barnsley, 4 x Dundee

Rock Scrubber & Brush Skimmer

Application

The floating skimmer head has two brush wheels which rotate to recover heavy oil. The heavier oils stick to the brushes and then get scrapped off by blades into a sump. The sump is connected to a small suction pump or power pack which delivers the oil to collection tanks. The rock scrubber unit works on the same principle but is portable and is configured to allow the rotating brush to reach rock faces and quaysides.

Locations

Brush Skimmer – 1 x Barnsley, 1 x Dundee, 1 x Bristol

Rock Scrubber – 1 x Barnsley, 1 x Dundee, 1 x Bristol

Specification	Rock Scrubber	Brush Skimmer
Recovery rate	2-6m3/per hour	12m3/per hour
Dimensions	1500 mm x 400 mm	840 mm x 660 mm x 320 mm
Weight	15 kg	26 kg

Trailer Mounted Rope Mop Skimmer

Application

A rope mop skimmer employs long continuous loops of oleophilic polypropylene material that floats on water. The rope is guided over the water surface by one or more pulley secured at convenient locations. The rope loop is pulled through a wringer that removes the oil.

Specification

A trailer mounted diesel driven OM2600 Ro-mop with floating pulleys. Oil is recovered into a tank under the Romop unit and has a recovery rate of 12m3/hr which can then be pumped to a storage tank and/or be removed as waste.

Dimensions

1760 mm x 820 mm x 1220 mm

Weight

460 kg

Locations

1 x Bristol, 1 x Dundee

Temporary Storage Tanks

Application

A portable, temporary storage system, for the containment of recovered oil on the shoreline. It can also be used as reservoir or pool for cleaning of oiled materials or wildlife.

Specification

There are 65x 10,000L fast tanks and 10x 7,500L fast tanks. The fabric is made of PVC coated polyester, which is U.V. resistant. The frame is aluminium. A ground sheet, pipe saddle and decanting valve are provided.

Ancillaries

Polythene lines, hand-pumps, pipe-saddles.

Dimensions

1640mm x 420mm x 460mm

Weight

64 kg

Locations

Barnsley, Bristol and Dundee

Fast Tank Rapides

Application

The Fastank Rapide acts as an oil spill clean-up/decontamination pool, used for the cleaning of personnel and equipment during an incident. It also works as a pool for splash protection, containment of leaks, animal cleaning or storage of soiled sorbent. It is light and can be handled and assembled by one person.

Specification

1500L capacity

Ancillaries

Polythene lines, hand-pumps, pipe-saddles.

Locations

Barnsley, Bristol and Dundee

Dimensions

1.72m x 1.67 x 0.6m (68” x 66” x 24”)

Weight

15Kg

All Terrain Vehicle (ARGO Cat Avenger)

Application

These all-terrain vehicles, which are also semi-amphibious, can be used to access areas inaccessible to road vehicles, such as mud flats. The vehicles feature eight 25” (635mm) diameter low-pressure tyres and tracks to provide a light foot print on sensitive terrain, resulting in low environmental impact. They can travel up to 30mph. Each vehicle features a towable trailer for transporting equipment.

Specification

The vehicle has a 31hp Daihatsu petrol engine. Vacuum formed lower hull and skid plate are formed from high density polyethylene (HDPE). The frame is powder coated, 3” tubular steel of welded construction.

Maximum speed:

30 mph.

Air Tent

Application

An inflatable tent designed to be quickly erected to provide shelter on site for exercises and deployments

Specification

Each tent has its own constant feed/loss air blower and provides space for approximately 20 people.

Locations

6x Barnsley, 2x Bristol, 2x Dundee

Fence Boom

Application

Designed to provide rapid oil spill containment, for use as either containment or spur boom in harbours, marinas, or enclosed coastal waters. The boom will fail in increased an increased sea state or current.

Specification

Solid buoyancy boom manufactured from PVC/Nitrile rubber impregnated onto polyester woven fabric. Encapsulated closed cell foam buoyancy blocks have been individually welded to the outer panels, which means they cannot get waterlogged if the boom becomes damaged. These are additionally stiffened with vertical fibre reinforced battens that add support. The foam blocks have a special memory property so when compressed onto a reel it retains the original shape and size as on deployment. The galvanised ballast chain has overall breaking strain in excess of 15 tonnes. The MCA stockpile has 200 metres of Fence boom stored on a reel, which is driven by a power pack for deployment and recovery purposes.

Dimensions

3040mm x 1975mm x 2000mm

Weight

1740 kg

Locations

600m Barnsley, 400m Dundee, 400m Bristol

Shore Sealing Boom

Application

A specialised boom designed for forming land surface seals, e.g. on inter tidal zones, river banks, mud flats. etc.

Specification

The boom is made of polyurethane coated nylon fabric, with aluminium Unicon connectors in 10 and 20 metre lengths. It consists of three tubes. The top tube is inflated for buoyancy and the bottom two tubes are filled with water for ballast and sealing purposes. Both air and water insertion take place through Monson valves for which Monson adaptors are required the air blowers and water pumps. Pressure relief valves are fitted to the water tube to avoid over pressurizing.

Ancillaries

Transport box, ancillary cage, Bruce or Seaclaw anchors, tripping buoys, chain, mooring stakes, sledgehammers.

Dimensions

280mm freeboard

280mm draft

560mm high

Weight

20 metre length 70 kg

Locations

Stored in all three bases – Barnsley, Dundee and Bristol

Inshore Inflatable Skirt Boom

Application

Containment / spur boom for shoreline, estuarine, harbour and river use.

Specification

Made from polyurethane-coated nylon fabric with aluminium Unicon connectors. Steel wire hawser provides tension and ballast. Monson valves each end for air inflation.

Ancillaries

Transport box, ancillary cage, Bruce or Seaclaw anchors, tripping buoys, chain, mooring stakes, Tirfor winches, sledgehammers.

Dimensions

330mm freeboard

405mm draught

735mm high

Weight

65 kg per 20 metre length

Location

Stored in all three bases – Barnsley, Dundee and Bristol

Rapid Deployment Solid Floatation Boom (Boombag)

Application

A rapid deployment containment system for use in sheltered waters such as harbours, inlets, lochs, estuaries and sounds. The system is comprised of 200m of solid floatation boom stored in a zig zag formation inside the 20m Boombag. The bag can be towed at speeds of up to 15 knots to the scene of an incident. Once the sea anchor is released the boom can be deployed in less than 60 seconds around a casualty to contain a spill or in a defensive formation to deflect oil from an object or area. The bag is deployed from s 20ft skid positioned on a quayside or slipway. It can be towed into the water from a height.

Quantity

3 x 200m Barnsley

Dimensions

On Pod – 18ft x 8ft, 3 meters

Weight

1350kg

Disc Skimmer

Application

A portable oleophilic disc skimmer for use on light to medium oils. The discs will be ineffective against dispersed or moussed/emulsified oil. The system is ideal as a portable skimmer in shallow water situations such as harbours, marinas or beaches.

Specification

The skimmer has 32 plastic discs driven by 2 hydraulic motors from a remote diesel hydraulic power pack. It weighs 60kg and has an operating draught of 24cm. Recovered oil in the sump is discharged through a 3” line to a Spate diaphragm pump fitted to the power pack. This skimmer is rated at 12 tonnes/hour with crude oil and 2 tonnes/hour in gas/diesel oil. Oil to water ratio maybe as high as 90%.

Ancillaries

Power pack, pump and spares box.

Dimensions

Skimmer Head 1280mm x 1280mm x 830mm

Power Pack 990mm x 940mm x 860mm

Weight

Skimmer Head 60kg

Power Pack 210kg

Sorbent Boom

Application

Sorbent booms are used to absorb thin layers of spilled oil. They are particularly useful in removing sheens of spilled light oils, e.g. marine diesel fuel. Sorbent boom consists of a fibre filling that absorbs the spilled oil while allowing water to pass through. The fibre filling is a special polypropylene crimped fibre opened and blown into the fabric. The fabric is specially treated to make it hydrophobic (repels water). The material is already oleophilic, (has an affinity for hydrocarbons). The fabric cover is produced from polypropylene yarn, which is woven with sufficient picks to allow total enclosure of the fibre whilst allowing an ingress of oil.

Dimensions

Nominal 8” wide and 10’ long

Location

Small quantities of sorbent boom are stored in each of our sites, Barnsley, Bristol and Dundee.

Dispersant

Application

Oil dispersant is a chemical formulated to break up oil and disperse oil into smaller particles, facilitating bioremediation. The dispersant can be either sprayed aerially using dedicated aerial spraying platforms or from a vessel using the Boat Spray Sets or the Boom Vane Spray set. The MCA, on behalf of the UK, holds a stock of over 1170 tonnes of Type 3 dispersant. The brands of dispersant held are Corexit, Dasic Slickgone NS,Dasic Slickgone EW, Dasic Slickgone LSTW, Agma, Super Dispersant 25, Finasol and Enesperse.

Dimensions

1m3 IBC

Weight

1000 kg

Locations and quantities

Type	Milford Haven	Glasgow	East Midlands	Shetland	Stornoway	Belfast	Prestwick Airport	Totals for Stockpile
Dasic Slickgone NS	17	79	86	0	0	29	0	211
Dasic Slickgone LSTW	3	21	17	39	0	0	0	80
Dasic Slickgone EW	0	10	9	0	0	0	0	19
Superdispersant 25	6	242	225	0	0	0	49	522
AGMA Superconcentrate DR 379	0	119	83	0	31	0	0	233
Finasol OSR 51	0	48	22	0	0	0	0	70
Enersperse 1583	0	0	21	3	0	0	0	24
Corexit 9500A	0	0	11	0	0	0	0	11
Totals per site	26	519	474	42	31	29	49	1170

Boat Spray Set

Application

The boat-spray 100TS is a portable diesel powered dispersant spray system for the application of concentrated or diluted dispersant from a specially designed even droplet nozzle with a port and starboard feature which have been introduced as an alternative to spray arms.

Dimensions

1250mm long x 1250mm x 1000mm high

Weight

301kg

Location

2 x Bristol, 2 x Dundee, 1 Belfast, 1 Stornoway

Boom Vane Spray

Application

A dispersant spraying system that utilises a Boom Vane with an attached mast support a 25-metre line and hose nozzle/hose assembly out to the starboard side of the deploying vessel which applies neat dispersant at a rate of up to 107 litres per minute.

Quantity

1x system at Barnsley

Dimensions

10ft Container in storage, 25meters when deployed.

Ancillaries

Inert Gas generator

Application

This unit is used to generate large quantities (2000m3/hr) of inert gas that will not support or sustain ignition of what would be flammable vapours given off by hydrocarbons. Precisely controlled combustion of fuel oil at the burner produces flue-gas typically composed of 1.0 to 1.5% Oxygen, 14% Carbon Dioxide, 100ppm Carbon Monoxide, and the remains of Nitrogen.

The unit is one of only a few portable inert gas generators in Europe and is operated in conjunction with a self-contained, electrical generator, and an accessories container.

Dimensions

Inert Gas Generator: 3150mm x 1500mm x 2400mm

Electrical Generator: 3150mm x 1350mm x 2200mm

Accessories Container: 2000mm x 1550mm x 1700mm

Weight

Inert Gas Generator: 3000kg

Electrical Generator: 2000kg

Accessories Container: 1000kg

Location

Barnsley

Multi-Purpose Hydraulic Power Pack(s)

Application

Small portable diesel engine driven hydraulic power packs which can be used to power a number of systems including skimmers, pumps and boom reels.

Specification

The unit has three hydraulic systems of different size and flows and can be configured to operate in 3 modes; High Flow/Low Torque, Low Flow/Low Torque or Low Flow/High Torque. It can power both a pump and a skimmer simultaneously or a boom reel on its own. It is mounted within a crash frame which includes lifting points and forklift pockets.

Dimensions

1210mm x 780mm x 940mm

Weight

191kg

Location

7 x Barnsley, 3 x Dundee, 2 x Bristol

Diesel Driven Hydraulic Power Packs

Application

There are three different types of hydraulically or mechanically started diesel engines which drive hydraulic pumps, all are self-contained with hydraulic oil and fuel oil tanks, mounted on a skid for transportation. These units have no electrical components and insulated exhausts and are therefore are safe to use in hazardous environments. Their primary function is to be used in conjunction with a back-up unit, and cargo transfer pumps, but can be used to power other large hydraulically driven equipment such as large skimmers.

Locations

Power Pack / Back up unit	Location	Total
Framo Power Pack	Barnsley x4, Bristol x1, Dundee 1	6
Vikoma Mark I	Bristol x1, Dundee x1	2
Vikoma Mark II	Barnsley x2	2
Back Up Unit	Barnsley x2, Bristol x1, Dundee x1	4

Power Pack	Weight (Kg)	Length (mm)	Width (mm)	Height (mm)
Framo On Skid	2350	2400	2000	2000
Framo	1250	2000	900	750
Vikoma IS	1300	2100	930	1750
Back Up 1300	2400	2000	2000	2000

Power Pack	Weight (kg)	Length (mm)	Width (mm)	Height (mm)
Framo on Skid	2350	2400	2000	2000
Framo	1250	2000	900	750
Vikoma IS	1300	2100	930	1750
Back Up Unit	1300	2400	2000	2000

Heavy Oil Pump

Application

A hydraulically driven pump set designed primarily to pump highly viscous fluids such as heavy fuel oil, bitumen, crude or sludge

Specification

The unit comprises a skid mounted diesel driven power pack, pump set and reels with hoses. The pump is a submersible positive displacement pump with a capacity of up to 140m3/hr, and includes water/steam injection and a debris cutting knife in the inlet

Dimensions

2810mm x 1460mm x 1680mm

Location

1 x Barnsley

Spate Pump

Application

Principally used as a transfer pump for oil or water. Can be used for fluid transfer between temporary storage facilities.

Specification

The unit is a self-priming, induced flow, diaphragm pump. When used on water a suction lift of up to 9 metres is attainable, a delivery head of 30 metres is possible and the maximum rated capacity is approximately 30 tonnes per hour. The performance of the pump diminishes the higher the viscosity of the liquid being pumped, meaning the more viscous the oil the lower the capacity that can be pumped.

Weight

180 kg

Dimensions

1160 x 820 x 1000 mm

Location

Barnsley, Bristol and Dundee

Cargo Transfer Pumps

Application

Cargo pumps can be used during salvage operations to transfer oil or chemicals between tanks or to remove oil or chemicals to another ship. The TK series of pump heads are centrifugal pumps. The pump head is submerged in the fluid to be pumped. Two pump heads can be powered by a single hydraulic power pack that is driven by a diesel engine.

Specification

The flow rate of the pumps varies with fluid viscosity and the ‘head’ (vertical distance) to be pumped.

Nominal maximum flow rates are:

Pump Head	Nominal Max. Pump Rate (m3 / per hour)	Static Head (Metre water column)
TK80	80	70mwc
TK5	190	50mwc
TK150	300	60mwc
TK6	500	40mwc

Weights and dimensions

Pump Head	Weight(kg)	Diameter (mm)	Height(mm)	Notes
TK 80	25	250*	625	Chemical/water
TK 5	60	298*	653	Chemical/water
TK150	78	300*	609	Chemical/water
TK6	85	520	700	Heavy oil or water

*Pump will fit through Butterworth Hatch

Locations

Pump heads	Type	Location	Total
TK80	Oil/ Water	Barnsley x 2, Bristol x1, Dundee	4
TK80	Chemical	Barnsley x 2	2
TK5 (s/s Hoses)	Chemical/Water	Barnsley x 2	2
TK5	Chemical/Water	Barnsley x1, Dundee x1	2
TK150	Chemical/Water	Barnsley x 2, Dundee x1, Bristol x1	4
TK6	Oil / Water	Barnsley x 4, Dundee x3, Bristol x1	8

Gas Freeing Fans

Application

These fans fit standard deck openings (12.5”) and can supply air or extract air vapour from a cargo tank. They are air-driven and intrinsically safe meaning they can be used around flammable gases if needed.

Specification

Victor Pyrate Type 850A Moves 8000 m3/hour with a compressed air supply at 7.5 bar Each fan has 10 metre sections of flexible ducting or 2 metre exhaust stack.

Dimensions:

463mm x 590mm diameter

Weight:

25 kg

Location:

4 x Barnsley

General Purpose Air Compressors

Application

Several standard duty compressors are held for normal operating conditions to drive pumps, fans, lighting or tools.

Location

2 x Barnsley

Safe Zone Compressor

Application

This compressor is designated as a ‘Safe zone’ Compressor. This means it is built with additional safety features for operation in ‘safe zones’ on offshore platforms. These safety features include an intake shutdown device that, in the event that flammable gases enter the engine, will shut the unit down. No electrical components are used, effectively eliminating the chance of sparks.

The unit is housed in a DNV 2:7-1 Offshore spec crash frame and lifting rig.

It is used to supply compressed air at 200cfm primarily to drive intrinsically safe air powered lighting, or to drive air driven gas-freeing fans.

Dimensions

2140mm x 2200mm x 1860mm high

Weight

2400 kg

Location

1 x Barnsley

Inflatable Fenders

Application

The Dunlop low-pressure fenders are rapidly transportable and can be easily inflated to provide damage protection during ship-to-ship transfer operations.

There are two sizes that are currently stored as part of the stockpile: a 4 x 1 metre in diameter x 4-metre-long and a 2 x 2 metre diameter x 12 metres long. (Sizes are when fully inflated)

Dimensions

The fenders are transported in cages that are:
2500mm long x 1700mm wide x 1350mm high

Weight

Small fender: 50kg
Large fender: 200kg

Locations

2 x Barnsley (large), 2 x Bristol (small), 2 x Dundee (small).

Self-Contained Lighting Rigs and Portable Lighting Systems

Application

Self-contained diesel driven 8 metre lighting towers consisting of 2 x 1000-watt halogen lamps. 2 x Ampco Intrinsically Safe Light System (1 x generator, 4 x floodlights per system)

12 x Wolf air driven turbo lamps. 6 Units can be driven on a standard air compressor.

Location

20x Barnsley

Contact information

For non-urgent enquiries:

Counter Pollution and Salvage Branch, Resources and Claims Lead –

• Jerry Connors: [email protected]
• Counter Pollution: [email protected]

For all marine or shoreline pollution incidents the first point of contact is the Coastguard, who can be reached by dialling 999 and asking for the Coastguard.

This catalogue is produced by:

The Maritime and Coastguard Agency
Spring Place
105 Commercial Road
Southampton
SO15 1EG